advertisement


Recent content by keithsnaim

  1. keithsnaim

    [FS] Hacker caps, toroid, etc

    Offered for sale has I no longer have use for them. Two pairs of Hacker caps using the original white pcbs. 1 pair with 80Vx6800uf caps, and high speed rectifiers. Wire links in place. £85 includes postage within the UK. 1 pair with CrCrC configuration, 100Vx2200uf caps and high speed...
  2. keithsnaim

    Building a LP12 from scratch

    Next job up is to corner brase the plinth. Anyone got the dimensions of these. I've looked at a few threads but can't find any sizes.
  3. keithsnaim

    [SWAP] Swap/PX/ Naim/Linn/Technics/SME

    It seems to me that it's down to how much you are willing to accept if you go down the sale route. I personally have Syrinx PU3 on my turntable. It's in pristine condition and much sought after, I also have its original box with everything that the arm came with. I personally would not let it...
  4. keithsnaim

    [SWAP] Swap/PX/ Naim/Linn/Technics/SME

    How old is the LP12 and what spec, this will help with the value.
  5. keithsnaim

    Building a LP12 from scratch

    Thanks guys for all your thoughts. I am weighing up all the possibilities. I have a good turntable already and this is a itch that I have to scratch.
  6. keithsnaim

    Building a LP12 from scratch

    That's the sort of info I was looking for. I have a large collection of 12" 45rpm discs too, so would require the pulley. I have taken up Martins offer of the Geddon clone to.
  7. keithsnaim

    Building a LP12 from scratch

    Thanks for your thoughts Tony, I've been looking at the various options on the auction sites and it seems that it would cost too much to get hold of 2 or 3 Lp12's to take the parts required. Plus I'm not keen about the bidding war that may develop. I like the idea of building at a steady pace...
  8. keithsnaim

    Building a LP12 from scratch

    That's interesting Simon. I take it that it's the same spec etc.
  9. keithsnaim

    Building a LP12 from scratch

    Well it's took me a long time to begin this build so any tips, advice etc would be gratefully received. I was given a LP12 plinth by a good friend many years ago. It has been stored in a box for a few years now in my loft. I took it out of the box 2 weeks ago to have a look at it with a view to...
  10. keithsnaim

    [WTD] OPA604 or OPA134

    Not sure if these are any good for you. I have 2 LT1115 op amps. These are unused and samples from the manufacturer. I got them for a phono stage that I built. Regards Keith
  11. keithsnaim

    Wanting to build NJ MMB, PhonoMB and 323, 321 & 729 cards - help needed

    I used a 2 watt resistor in the relay section next to the Led, you can see it in my monica photo.
  12. keithsnaim

    Wanting to build NJ MMB, PhonoMB and 323, 321 & 729 cards - help needed

    The Bc560c has much higher hfe than the Bc560a.
  13. keithsnaim

    Wanting to build NJ MMB, PhonoMB and 323, 321 & 729 cards - help needed

    Cricklewood electronics have the 2SK117, and BC560. You have the BOM for the phono motherboard, I emailed you earlier on this month. Keith.
  14. keithsnaim

    correct value for Volume pot - NJ MMB

    Think I used a Noble pot, 20K seems to ring a bell though.
  15. keithsnaim

    BOMs for NJ MMB and MMPhono boards - help needed

    http://i291.photobucket.com/albums/ll292/keithsnaim/image-11.jpg Found this of my build. Keith.


advertisement


Back
Top